Exmark Ultra Vac Uživatelský manuál

103.2 INSTALL DRIVE KIT1. Install drive kit (PN 103-1313, 103-1314, 103-1315, or 103-1317 depending on deck size)per the instructions included in t

11FIGURE 1BELT ROUTING3. Reinstall the belt guide removed in Step 1.4. Remove Discharge chute by pulling the hairpin and chute pivot pin (from the

12 WARNINGPOTENTIAL HAZARD♦ An uncovered discharge opening will allow objects tobe thrown in operator’s or bystander’s direction.Also, contact

13LAZER Z ASSEMBLY DIAGRAMLAZER Z XP ASSEMBLY DIAGRAMItems 21,22,26, 29, 30, 31 and 32 not shown. See figure 1 for installation of 31 and 32.See figu

144.2 INSTALL THE HOOD ASSEMBLY AND BAGSLazer Z units only (Lazer Z XP units skip to step 6)1. When installing the Ultra Vac onto a liquid cooled Laz

155. Install the side plates (Items 14 and 15) loosely to the mount weldment and the wheelchannels of the Lazer Z frame. The flanges on the side pla

167. Re-install the deck drive belt in the lower groove of the double sheave. Install theplug (Item 24) into the bore of the double sheave.8. Remov

17FIGURE 414. Using the knob that was removed with the original belt cover stud and the knob includedwith the completing kit (Item 40), mount the two

1820. 72” units below serial number 260,000 will require the deck to be modified by adding theaccessory mounting tube. Exmark kit 103-0583 contains t

192. Locate the position of the mounting holes. On machines with serial numbers less than320,000, clamping a weight plate to the front of the floor

2 WARNINGPOTENTIAL HAZARD♦ This product is a piece of power equipment.WHAT CAN HAPPEN♦ Failure to follow safe operating practices can resul

204.7 RUN IN – 52” UNITS ONLY1. Follow the operation instructions in Section 5 to run the unit. Run the unit with the bladesand blower engaged for

2122212. Ensure the blower, belt cover, bags, tube and hood are in good condition, properlyattached, and latched.5.2 MOWING1. The Ultra Vac blower op

227. Re-install the plastic belt cover and tighten the knobs.8. Remove the hair pins and clevis pins holding the hood assembly to the mount weldment

23 WARNINGPOTENTIAL HAZARD♦ Loading a unit on a trailer or truck increases the possibility ofbackward tip-over.WHAT CAN HAPPEN♦ Backward ti

246.1.2 Idler Bushings: Service Interval: 25 Hours.Lubricate with 1-2 pumps of SAE No. 2 multi-purpose grease.6.1.3 Bags: Service Interval: Daily.In

257. PARTS LISTS7.1 DECALSRef.No. Qty.Part No. Description Req'd.1 1-653557 Decal, Ultra Vac………………..12 103-0220 Decal, Warning Di

267.2 BLOWER ASSEMBLY – LAZER Z HP 44, 48, 52 & LAZER Z 52

277.2 BLOWER ASSEMBLY – LAZER Z HP 44, 48, 52 & LAZER Z 52 (cont.)Ref.No.Qty.Part No. Description Req'd.Ref.No. Qty.Part No. Description

287.3 HOOD AND BAG ASSEMBLY – LAZER Z HP 44, 48, 52, & LAZER Z 52

297.3 HOOD AND BAG ASSEMBLY – LAZER Z HP 44, 48, 52, & LAZER Z 52 (cont.)Ref.No. Qty.Part No. Description Req'd.Ref.No. Qty.P

3EXMARK PARTS PLUS PROGRAMEFFECTIVE DATE: September 1, 1995ProgramIf your Exmark dealer does not have the Exmark part in stock,Exmark will get th

307.4 BLOWER ASSEMBLY – LAZER Z 60 & 72 and LAZER Z XP 60 & 72

317.4 BLOWER ASSEMBLY – LAZER Z 60 & 72 and LAZER Z XP 60 & 72 (cont.)Ref.No.Qty.Part No. Description Req'd.Ref.No. Qty.Part No. Descr

327.5 HOOD AND BAG ASSEMBLY – LAZER Z 60 & 72 and LAZER Z XP 60 & 72

337.5 HOOD AND BAG ASSEMBLY – LAZER Z 60 & 72 and LAZER Z XP 60 & 72 (cont.)Ref.No. Qty.Part No. Description Req'd.Ref.No.

347.6 COMPLETING KIT ASSEMBLY – LAZER Z 52, 60, & 72; Lazer Z XP 60 & 72

357.6 COMPLETING KIT ASSEMBLY - LAZER Z 52, 60, & 72; LAZER Z XP 60 & 72(cont.)LAZER LAZER XP52” 60” 72” 60” 72”Ref.No.Part No. Description103

367.7 DRIVE KIT ASSEMBLY – LAZER Z HP 44,48Quantity Included in Each Kit44” 48” (w/4” tab) 48” (w/2” tab) 52”Ref.No.Part No. Description103-1315 10

378. WARRANTYLimited WarrantyExmark Commercial Turf EquipmentExmark Mfg. Co. Inc. and its affiliate, Exmark Warranty Company, pursuant to an agreemen

38As a condition to this warranty, customer shall have read the operator's manual and shall havecompleted and returned to Exmark Warranty Company

SERVICE RECORD Date Description of Work Done Service Done By

4OPERATOR'S MANUALThis manual contains assembly, operating, maintenance, adjustment and safety instructionsfor your Exmark Ultra Vac.BEFORE OPERA

®MFG. CO. INC.SEE EXMARK’S COMPLETELINE OF PRODUCTS FOR TURF CARELAZER Z®LAZER Z® HPLAZER Z® XPTURF RANGER®TURF TRACER®TURF TRACER® HPVIKING HYDROMETR

5TABLE OF CONTENTSDescription Page1. Safety1.1 Safety Alert Symbol...6

61. SAFETY1.1 SAFETY ALERT SYMBOLThis SAFETY ALERT SYMBOL is used both in this manual and on the machine toidentify important safety messages which

71.3.3 While mowing, always wear substantial footwear and long trousers. Do not operateequipment when barefoot or when wearing open sandals.1.3.4 Thor

82. SPECIFICATIONS2.1 MODEL NUMBER:LHPUV4448Use with drive kit: 44” deck – 103-131548” deck – 103-1313 (Lazer Z HP Serial Nos. below 203,376)48” d

93. ASSEMBLY INSTRUCTIONS – LAZER Z HP(See Section 4 for Lazer Z and Lazer Z XP)3.1 ASSEMBLY DIAGRAMRef. No. Qty Description1 Ref Engine Guard 44,48