Exmark VH3615KA Uživatelský manuál

- 5 -1.5.5 Keep the mower and fuel container in locked storage to prevent children fromplaying or tampering with them.1.5.6 Gasoline powered equipmen

- 6 -PART NO. 323741LOCATION: ConsolePART NO. 323691LOCATION: RH Side of ConsolePART NO. 303517LOCATION: Left Side of Rear

- 7 -2. SPECIFICATIONS2.1 MODEL NUMBER: Serial Nos. 220,000 & Higher: VH3615KA; VH4815KA 2.2 ENGINE2.2.1 Engine Specifications: See your E

- 8 -2.6.2 Hydraulic Filter is replaceable cartridge type.P/N 513211: 10 microns, 18 psi bypass (Summer use above 32° F)P/N 523541: 40 microns, 18 psi

- 9 - 2.11 TORQUE REQUIREMENTSBOLT LOCATION TORQUEBlade/Cutter Housing Spindle Bolt...75-80 ft-lbs.Caster Bracket Mou

- 10 -b) Loosen clamp on engine control plate (See Figure 2). Attach inner wire ofthe throttle cable to the control plate lever and position cable un

- 11 -3.13 Install the speed control rod assembly (linkage with the yoke installed on one end)into the end of the speed control lever located undernea

- 12 -4. OPERATION INSTRUCTIONS4.1 Controls4.1.1 Operator Presence Control (OPC) Levers: Located on the upper handleassembly directly above the handle

- 13 -Once the engine has started, move the throttle control lever to the midwaypoint and allow the engine to warm-up before going to full throttle.4.

- 14 -4.2.1 Fill fuel tank. For best results use only clean fresh regular grade unleadedgasoline with an octane rating of 87 or higher. Regular grade

ii WARNINGThe engine exhaust from this productcontains chemicals known to the State ofCalifornia to cause cancer, birth defects,or other repr

- 15 - WARNINGPOTENTIAL HAZARD♦ Engine exhaust contains carbon monoxide, which isan odorless deadly poison.WHAT CAN HAPPEN♦ Carbon monoxide

- 16 - CAUTIONPOTENTIAL HAZARD♦ If the neutral lock latches are not completely engaged thedrive levers could unexpectedly slip into the forw

- 17 -4.3.8 Blade Disengagement: Push forward and down completely on the engagementknob to disengage the blades (See Section 4.1.5).4.4 TRANSPORTING

- 18 -5.1 PERIODIC MAINTENANCE5.1.1 Check engine oil level.Service Interval: See Engine Owner's Manuala) Make sure engine is stopped and on a le

- 19 -h) Remove jack stands (or equivalent support) and lower deck to ground.FIG. 6BLADE BOLT INSTALLATION5.1.4 Check safety interlock system.Service

- 20 -d) Remove the oil drain plug from the right hand side of the engine. Allow oilto drain, then replace drain plug.e) Replace the oil filter as per

- 21 -e) Loosen filter 1/2 turn and allow a small amount of oil to leak from the oilfilter (this allows air to be purged from the oil filter and suppl

- 22 -e) To “prime” charge pump, loosen two hex socket head capscrews (shownin Figure 7) 1-1/2 turns only. Make sure engine is not running. Liftchar

- 23 -No. 4 Idler Pivot (Pump Drive)Located Under Engine DeckNo. 4 & 6 (Idler Pivots)Disassemble and grease once amonth under a “No Load” conditio

- 24 -c) OPC lever setscrews.d) Shoulder bolts in ends of speed control crank.e) Between the fuel tank studs and the fuel tanks.f) Between the shift

iiiEXMARK PARTS PLUS PROGRAMEFFECTIVE DATE: September 1, 1995ProgramIf your Exmark dealer does not have the Exmark part in stock,Exmark will get

- 25 -5.2.1 Blade Spacers:Blades may be adjusted for cutting height by using the four 1/4" spacers foundon the blade spindle bolts (factory setti

- 26 -FIG. 8AXLE and CASTER HEIGHT ADJUSTMENTRefer to the following chart to properly adjust desired cutting height.CUTTING HEIGHT ADJUSTMENT (1"

- 27 -b) With blade drive engaged (lever pulled up, adjust the linkage length towhere the lower end of the bellcrank just clears the axle support guss

- 28 -FIG. 10CUTTER DECK BELT ADJUSTMENTe) Proper belt tension will require about 10 lbs. side pull on belt, halfwaybetween pulleys, to deflect belt 1

- 29 -Note: These drawings are viewed from underneath the engine deckFIG. 12 FIG. 1336" BELT GUIDE LOCATION 48" B

- 30 -Make sure you have not reached the end of the neutral lock latch slot.If you have, shorten the drive lever linkage. If the wheel turns whilehold

- 31 -After adjusting the left hydro control linkage, move the speed controllever to the mid-speed position and then back to the neutral position.Rech

- 32 -4. If the unit tracks to one side or the other, turn the quick track knob .Turn the knob right to “steer” right, turn the knob left to “steer”

- 33 -e) Check that there is fuel in the tank and that the fuel valve is open.f) Check that the spark plug wire(s) are properly connected.g) Check for

- 34 -8. WIRING DIAGRAM

ivCONGRATULATIONS on the purchase of your Exmark Mower. This product has been carefullydesigned and manufactured to give you a maximum amount of depen

- 35 -9. HYDRAULIC DIAGRAM

- 36 -10. WARRANTYLimited Warranty Exmark Commercial Turf Equipment Exmark Mfg. Co. Inc. ("Exmark")warrants on the terms and conditions here

- 37 -As a condition to this warranty, customer shall have read the operator's manual and shall havereturned to Exmark, within the prescribed tim

- 38 -THIS IS A 15° SLOPETHIS IS A 10° SLOPETHIS IS A 5° SLOPEALIGN THIS EDGE WITH A VERTICAL SURFACE(TREE, BUILDING, FENCE POST, POLE ETC.)EXAMPLE: C

SEE EXMARK’S COMPLETELINE OF PRODUCTS FOR TURF CARELAZER Z™LAZER Z™ HPTURF RANGER®TURF TRACER®TURF TRACER® HPVIKING HYDROMETRO™METRO™ HPSELF STEERING

TABLE OF CONTENTSv1. SAFETY ...PAGE1.1 Safety Alert

- 1 -1. SAFETY1.1 SAFETY ALERT SYMBOLTHIS SAFETY ALERT SYMBOL IS USED BOTH IN THIS MANUAL AND ONTHE MACHINE TO IDENTIFY IMPORTANT SAFETY MESSAGES WHI

- 2 - WARNINGPOTENTIAL HAZARD♦ Engine exhaust contains carbon monoxide, which isan odorless deadly poison.WHAT CAN HAPPEN♦ Carbon monoxide

- 3 - DANGERPOTENTIAL HAZARD♦ In certain conditions gasoline is extremely flammableand highly explosive.WHAT CAN HAPPEN♦ A static charge ca

- 4 -1.4.5 Stop the blades when crossing surfaces other than grass; and whentransporting the mower to and from the area to be mowed.1.4.6 Never operat