Exmark Lazer ZXS Uživatelský manuál

For Serial Nos. 600,000 & Higher Part No. 103-9911 Rev. A

- 5 - • See inside the back cover to determine the approximate slope angle of the area to be mowed. • Progressively greater care is needed as th

- 6 - 1.4.16 This mower was designed for one operator only. Keep all others away from mower during operation. 1.4.17 Do Not mow with the di

- 7 - PART NO. 1-303518 LOCATION: Transmission Shifter Plate PART NO. 1-513746 LOCATION: Engine B

- 8 - Pistol Grip Handle Units PART NO. 1-323550 LOCATION: Upper Handles (Both Sides) PAR

- 9 - 2. SPECIFICATIONS 2.1 MODEL NUMBER: M15KA322P; M15KA362P; M15KA483P; M15KA362; M15KA483 2.2 ENGINE 2.2.1 Engine Specification

- 10 - 2.9.3 Blade Size: Model 32 ...16.25 (41.3 cm) - Qty. 2 Model 36 ...18.00 (45.7 cm) - Qty. 2 Model 48 ...16.25

- 11 - will kill the engine if either the transmission shift lever is not in the neutral position or the PTO is engaged. See Figures 1 and 2. 3

- 12 - 3.1.5 PTO Engagement Lever: Located on the left side of the upper handle. To engage the blades, push the lever forward, or

- 13 - 3.3 OPERATING INSTRUCTIONS 3.3.1 Read the Engine Owner's Manual carefully for detailed operating instructions and maintenance

- 14 - FIGURE 3 DRIVE LEVER, NEUTRAL LOCK/PARK BRAKE OPERATION For ECS Handles: To lock the drive levers in “neutral lock”, sque

i WARNING POTENTIAL HAZARD ♦ This product is a piece of power equipment. WHAT CAN HAPPEN ♦ Failure to follow safe operating practices c

- 15 - FIGURE 4 DRIVE LEVER, NEUTRAL LOCK/PARK BRAKE LATCH OPERATION 3.3.5 Drive Wheel Engagement and Turning: With drive

- 16 - DANGER POTENTIAL HAZARD ♦ An uncovered discharge opening will allow objects to be thrown in an operator’s or bystander’s direction. Also

- 17 - 4. MAINTENANCE AND ADJUSTMENTS 4.1 PERIODIC MAINTENANCE WARNING POTENTIAL HAZARD ♦ While maintenance or adjustments are being made,

- 18 - 4.1.3 Clean grass build-up under deck and check mower blades. Service Interval: Daily CAUTION POTENTIAL HAZARD ♦ Rai

- 19 - Again, run the engine at one-third throttle, move the transmission shifter lever to neutral, engage the PTO and release the OPC leve

- 20 - 3/16” TO 1/4”(.47-.64 cm) Drive Linkage Neutral Lock / Park Brake Latch FIGURE 7 PISTOL GRIP HANDLES NEUTRAL LOCK LEVER CLEAR

- 21 - FIGURE 9 ECS HANDLE DRIVE LEVER LINKAGE INSTALLATION 4.1.6 Check for loose hardware. Service Interval: Daily

- 22 - 4.1.9 Check tire pressures. Service Interval: Pneumatic (air-filled) Drive Tires- 40 hrs. Semi-pneumatic Caster Tires –

- 23 - LUBRICATION CHART FITTING LOCATIONS INITIAL PUMPS FITTING QUANTITY 32" 3 6" 4 8 " SERVICE INT

- 24 - 4.1.18 Thread locking adhesives Fel-Pro Pro-Lock "Nut-Type" or Loctite Threadlocker "242" are used on the following

ii EXMARK PARTS PLUS® PROGRAM EFFECTIVE DATE: September 1, 1995 Program If your Exmark dealer does not have the Exmark part in stock, Exmark wil

- 25 - d) Loosen but do not remove the two (2) axle pivot bolts and the two (2) axle adjustment bolts (See Figure 11). e) Place a jac

- 26 - CUTTING HEIGHT ADJUSTMENT (1" to 4 1/4") AXLE POSITION (FIG. 20) # OF SPACERS BELOW CASTER SUPPORT HUB NUMBER OF 1/4" BLADE S

- 27 - c) Belt must be tight enough to not slip during heavy loads while cutting grass. Overtensioning will reduce belt and spindle bearing

- 28 - FIGURE 13 BLADE BRAKE ADJUSTMENT 4.2.7 Belt Guide Adjustment a) Stop engine and wait for all moving parts to stop. Rem

- 29 - FIGURE 18 SHIFTER LEVER TO TRANSMISSION To adjust the shifter lever: a) Remove the 3/8" nyloc nut and spring disk washer from th

- 30 - FIGURE 19 UPPER HANDLE HEIGHT ADJUSTMENT 4.2.14 Wheel drive spring tension adjustment. It may be necessary to increase

- 31 - b) Check to be sure idler arms pivot freely, if not, lubricate idler pivots. c) Check for worn drive belts. NOTE: Wheel drive belt

- 32 - ENGINE TROUBLESHOOTING TABLE PROBLEM NO FUEL IMPROPER FUEL DIRT IN FUEL DIRTY AIR FILTER FAULTY SPARK PLUG ENGINE OVER- LOADED BLOCKED FU

- 33 - 9. 2-Year Limited Warranty Exmark Turf Equipment (For units purchased on or after

- 34 - 10. Evaporative Emission Control Warranty Statement California Evaporative Emission Control Warranty Statement Your Warranty Rights and

iii CONGRATULATIONS on the purchase of your Exmark Mower. This product has been carefully designed and manufactured to give you a maximum amo

- 35 - NOTES

- 36 - NOTES

- 37 - SERVICE RECORD Date Description of Work Done Service Done By

- 38 - THIS IS A 15° SLOPETHIS IS A 10° SLOPETHIS IS A 5° SLOPEALIGN THIS EDGE WITH A VERTICAL SURFACE(TREE, BUILDING, FENCE POST, POLE ETC.)EXAMPL

®MFG. CO. INC.SEE EXMARK’S COMPLETE LINE OF ACCESSORIES RIDING ACCESSORIES CUSTOM RIDE SEAT SUSPENSION SYSTEM DECK LIFT ASSIST KIT HITCH KIT LIGHT

iv TABLE OF CONTENTS 1. SAFETY PAGE 1.1 Safety Alert Symbol ...

- 1 - 1. SAFETY 1.1 SAFETY ALERT SYMBOL This SAFETY ALERT SYMBOL is used both in this manual and on the machine to identify important safety me

- 2 - 1.3.4 Thoroughly inspect the area where the equipment is to be used and remove all stones, sticks, wires, bones, and other foreign objects

- 3 - DANGER POTENTIAL HAZARD ♦ In certain conditions gasoline is extremely flammable and highly explosive. WHAT CAN HAPPEN ♦ A static ch

- 4 - WARNING POTENTIAL HAZARD ♦ Operating engine parts, especially the muffler, become extremely hot. WHAT CAN HAPPEN ♦ Severe burns can oc