Exmark Metro 26 Uživatelský manuál

For Serial Nos. 510,000 & Higher Part No. 103-9832 Rev. A

- 5 - 1.4.8 Do Not change the engine governor settings or overspeed the engine. Operating an engine at excessive speed may increase the hazard of

- 6 - 1.5.8 Keep all guards, shields and safety devices in place and in safe working condition. 1.5.9 Frequently check for worn or damaged

- 7 - 2. SPECIFICATIONS 2.1 MODEL NUMBER: M266KASPC 2.2 ENGINE 2.2.1 Engine Specifications: See your engine owner&apos

- 8 - 3. ASSEMBLY INSTRUCTIONS NOTE: Determine the left and right sides of the machine from the normal operating position. 3.1 Installing t

- 9 - 6. Secure the fuel line in place with the fuel line clamp (Fig. 3). 3.3 Service the Engine 3.3.1 Filling the Crankca

- 10 - 4.1.3 Self-Propel Drive Bail: Located on the upper handle as shown in Figure 5. When the self-propel drive bail is squ

- 11 - 4.2 PRE-START 4.2.1 Refer to Section 5 Maintenance and perform all of the necessary inspection and maintenance steps. 4.2.2 Fi

- 12 - 2. Open the fuel valve. The fuel valve is located at the lower left edge of the fuel tank. Rotate the valve counter-cloc

- 13 - speed. Move the ground speed control to the Neutral position when you use the lawn mower for trimming or whenever you leave the lawn mower.

- 14 - 14. Pull the lawn mower away from the newspaper. If the newspaper ball unravels or is shredded, the blade has not properly stopped, re

- i - WARNING POTENTIAL HAZARD ♦ This product is a piece of power equipment. WHAT CAN HAPPEN ♦ Failure to follow safe operating practic

- 15 - Front wheel height adjustment: 1. Pull the wheel height adjustment lever toward the wheel (Fig. 11) and move it to the desired sett

- 16 - 3. Set the bag frame onto the bag support tabs. 4. Lower door onto bag. Mowing with the Grass Bag WARNING POTENT

- 17 - 4.3.10 Operating Tips • Review the Safety Instructions (Section 1) and read this manual carefully before operating the lawn mower. • Set

- 18 - 5. MAINTENANCE NOTE: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedul

- 19 - 5.2 Checking the Blade Brake Clutch Refer to Section 4.3.6 Checking the Blade Brake Clutch. 5.3 Cleaning the Underside of the Law

- 20 - 4. Remove the dirt and grass clippings with a hardwood scraper. Avoid burrs and sharp edges. 5. Turn the lawn mower upright. 6.

- 21 - NOTE: Do not try to clean a paper air filter. 6. Remove the foam pre-cleaner and wash it with a mild detergent and

- 22 - NOTE: For the best performance, install a new blade before the cutting season begins. During the year, file down any

- 23 - 9. Re-install a sharp balanced Exmark blade, spacer, washer, and blade bolt. The sail of the blade must point toward the top of the law

- 24 - 2. Locate the grease fitting on the underside of the mower deck. Wipe the grease fittings with a clean rag (Fig. 23).

- ii - EXMARK PARTS PLUS® PROGRAM EFFECTIVE DATE: September 1, 1995 Program If your Exmark dealer does not have the Exmark part in stock, Exmark

- 25 - 0.030 in. (0.76 mm) 6. Install the spark plug and the gasket seal. 7. Torque the plug to 17 ft-lb (23 N-m). 8. Connect the

- 26 - WARNING POTENTIAL HAZARD ♦ Oil may be hot after engine has been run. WHAT CAN HAPPEN ♦ Contact with hot oil can cause severe per

- 27 - 4. Gently apply one to two pumps of #2 multi-purpose lithium-base grease. 5. Re-install gear case access cover. 6.

- 28 - FRONT WHEEL ASSEMBLY REAR WHEEL ASSEMBLY FIGURE 30 FIGURE 31 Assembling the Wheels

- 29 - 3. Using an oil can, add about one tablespoon of oil to the crankcase through the spark plug hole. 4. Slowly rotate the engine several

- 30 - 8. TROUBLESHOOTING Exmark designed and built your lawn mower for trouble free operation. Check the following components and items carefull

- 31 - Problem Possible Causes Corrective Action 1. The blade is bent or is out of balance. 1. Balance the blade. If the blade is bent, repla

- 32 - 9. 2-Year Limited Warranty Exmark Turf Equipment (For units purchased on

- 33 - NOTES

- 34 - SERVICE RECORD Date Description of Work Done Service Done By

- iii - CONGRATULATIONS on the purchase of your Exmark Mower. This product has been carefully designed and manufactured to give you a maximum

®MFG. CO. INC. SEE EXMARK’S COMPLETE LINE OF ACCESSORIES RIDING ACCESSORIES CUSTOM RIDE SEAT SUSPENSION SYSTEM DECK LIFT ASSIST KIT HITCH KIT LIG

- iv - TABLE OF CONTENTS 1. SAFETY PAGE 1.1 Safety Alert Symbol...

- 1 - 1. SAFETY This lawn mower meets or exceeds the CPSC blade safety requirements for walk-behind rotary mowers and the B71.4 specifications of

- 2 - 1.3.3 While mowing, always wear substantial footwear and long trousers. Do not operate equipment when barefoot or when wearing open sandal

- 3 - DANGER POTENTIAL HAZARD ♦ In certain conditions gasoline is extremely flammable and highly explosive. WHAT CAN HAPPEN ♦ A static ch

- 4 - WARNING POTENTIAL HAZARD ♦ Hands, feet, hair, clothing, or accessories can become entangled in rotating parts. WHAT CAN HAPPEN ♦ Cont