Exmark Metro HP Uživatelský manuál

Part No. 103-9184For Serial Nos. 540,000 & Higher

- 5 -• See inside the back cover to determine the approximate slope angle of the area to be mowed. • Progressively greater care is needed as the

- 6 -1.4.17 Do Not mow with the grass deflector raised, removed or altered unless there is a grass collection system or mulch kit in place and worki

- 7 - PART NO. 1-303508 LOCATION: Front of Mower Deck, Top Surface PART NO. 1-513746 LOCATION: On Engine Blower Housing next to Muffler &

- 8 - PART NO. 1-553049 LOCATION: Front of Mower Deck Top Surface PART NO. 103-7491 LOCATION: On Top LH Side of Mower Deck PART NO. 103-1623 LOCATI

- 9 -2. SPECIFICATIONS 2.1 MODEL NUMBER: MHP3615KAC; MHP4815KAC 2.2 ENGINE 2.2.1 Engine Specifications: See your Engine Owner&a

- 10 - 2.10 DIMENSIONS 2.10.1 Overall Width: 36” 48” Discharge chute down 46.25” (117.5 cm) 58.25” (148.0 cm)Discharge

- 11 -FIGURE 1 UPPER HANDLE MOUNTING 3.8 Route the throttle cable along the right side of the upper handle, through the clip, under the fuel tank

- 12 - 3.10 Install and adjust shifter lever. a) Remove the 3/8” nyloc nut and spring disc washer from the stud on top of the transmission

- 13 -b) The bend in the drive lever linkages should be positioned downward and slightly outward. If adjustment is needed, loosen jam nut below ba

- 14 - 3.12 Route the long unattached wiring harness lead, up the left hand side of the handle and connect the connector on the end of the shorter

ii WARNING POTENTIAL HAZARD ♦ This product is a piece of power equipment. WHAT CAN HAPPEN ♦ Failure to follow safe operating practices

- 15 - FIGURE 9 NEUTRAL LOCK/PARK BRAKE LATCH 4.1.5 PTO Engagement: Located on the left side of the upper handle. To engage the

- 16 - Do not add oil to gasoline. Do not overfill fuel tank. Never fill the fuel tank so that the fuel level rises above a level that is 1/2”

- 17 - FIGURE 10 DRIVE LEVER, NEUTRAL LOCK/PARK BRAKE LATCH OPERATION 4.3.5 Drive Wheel Engagement and Turning: With drive levers in

- 18 - DANGER POTENTIAL HAZARD ♦ An uncovered discharge opening will allow objects to be thrown in an operator’s or bystander’s direction. Also,

- 19 -5. MAINTENANCE & ADJUSTMENTS WARNING POTENTIAL HAZARD ♦ While maintenance or adjustments are being made, someone could start the eng

- 20 - b) Raise deck to the highest position. Lift the front of unit and support unit using jack stands or equivalent support. CAUTION POTE

- 21 - CAUTION POTENTIAL HAZARD ♦ Operating a mower deck with loose or weakened blade bolts can be dangerous. WHAT CAN HAPPEN ♦ A loose or w

- 22 - a) Stop engine and wait for all moving parts to stop. Remove key or spark plug wire(s). b) Drain oil while engine is warm from ope

- 23 - b) Remove deck support belt shield to check mower deck drive belt condition. c) Look under engine deck to check the transmission d

- 24 - d) Lubricate drive wheel hubs once a year. First remove wheel, then remove hub cap. Lubricate the grease fitting on each wheel hub wi

iii EXMARK PARTS PLUS® PROGRAM EFFECTIVE DATE: September 1, 1995 Program If your Exmark dealer does not have the Exmark part in stock, Exmark wi

- 25 - 5.1.21 Mobil HTS grease (or food-grade antisieze) is used in the following locations: a) Between the cutter housing spindle and bearin

- 26 - FIGURE 13 ANTI-SCALP ROLLER BOLT INSTALLATION ANTI-SCALP ROLLER AND CUTTING HEIGHT ADJUSTMENT c) Adjust anti-scalp rollers for Norma

- 27 - 5.2.4 Engine to Cutter Deck Belt: No adjustment necessary. 5.2.5 Transmission Belt Adjustment: a) Stop engine and wait for all

- 28 - FIGURE 15 DRIVE BELT TENSION ADJUSTMENT POSITIONS 6. WASTE DISPOSAL 6.1 MOTOR OIL DISPOSAL Engine oil is a pollutant to the e

- 29 - f) Check that the spark plug wire(s) are properly connected. g) Check for loose or faulty wiring connections. If it is necessary to

- 30 -8. WIRING DIAGRAM – 15 HP KAWASAKI

- 31 -9. 2-Year Limited Warranty Exmark Turf Equipment (For units purchased on

- 32 - NOTES

- 33 -SERVICE RECORD Date Description of Work Done Service Done By

- 34 - THIS IS A 15° SLOPETHIS IS A 10° SLOPETHIS IS A 5° SLOPEALIGN THIS EDGE WITH A VERTICAL SURFACE(TREE, BUILDING, FENCE POST, POLE ETC.)EXAMPLE:

iv CONGRATULATIONS on the purchase of your Exmark Mower. This product has been carefully designed and manufactured to give you a maximum amount of

®MFG. CO. INC.SEE EXMARK’S COMPLETE LINE OF ACCESSORIES RIDING ACCESSORIES CUSTOM RIDE SEAT SUSPENSION SYSTEM DECK LIFT ASSIST KIT HITCH KIT LIG

v TABLE OF CONTENTS 1. SAFETY... PAGE 1.1 Safety A

- 1 -1. SAFETY 1.1 SAFETY ALERT SYMBOL This SAFETY ALERT SYMBOL is used both in this manual and on the machine to identify important safety me

- 2 - 1.3.4 Thoroughly inspect the area where the equipment is to be used and remove all stones, sticks, wires, bones, and other foreign objects w

- 3 - DANGER POTENTIAL HAZARD ♦ In certain conditions gasoline is extremely flammable and highly explosive. WHAT CAN HAPPEN ♦ A static ch

- 4 - WARNING POTENTIAL HAZARD ♦ Operating engine parts, especially the muffler, become extremely hot. WHAT CAN HAPPEN ♦ Severe burns can occu